Power Transformers are suitable for high voltage (greater than 33KV) for power transfer applications. It is used in power generation stations and Transmission substation. It has high insulation level. Power transformers convert power-level voltages, as opposed to electrical signals, from one level or phase configuration to another. They are used to increase or decrease voltage to suit a specific application, and are widely used in electrical power distribution systems
VOLTACTIVE offers you the best quality assured transformer and we have vast experience in manufacturing .We would like to give you the life long service to your transformer.
We manufacture power transformers upto 5MV 33KV/11KV & 33KV/433V


In order to distribute the power generated from the power generation plant to remote locations, these transformers are used. Basically, it is used for the distribution of electrical energy at low voltage is less than 33KV in industrial purpose and 440v-220v in domestic purpose.

It works at low efficiency at 50-70%

  • Small size
  • Easy installation
  • Low magnetic losses
  • It is not always fully loaded

VOLTACTIVE offers you the complete range of Distribution Transformers designed according to our standards.We offer you different ranges of Distribution Transformer.

We manufacture Single phase-5kva&15kva & Three phase-25kva to 1000kva 11kv class


The Current Transformer ( C.T. ), is a type of “instrument transformer” that is designed to produce an alternating current in its secondary winding which is proportional to the current being measured in its primary. The basic principle of the current transformer is the same as that of the power transformer. Like the power transformer, the current transformer also contains a primary and a secondary winding. Whenever an alternating current flows through the primary winding, alternating magnetic flux is produced, which then induces alternating current in the secondary winding. In the case of current transformers, the load impedance or “burden” is very small. Therefore the current transformer operates under short circuit conditions. Also the current in the secondary winding does not depend on load impedance but instead depends on the current flowing in the primary winding.

Voltactive offers you the Current Transformers upto 132KV, 33KV, 11KV class with different ratings.


Potential transformer or voltage transformer gets used in electrical power system for stepping down the system voltage to a safe value which can be fed to low ratings meters and relays. Commercially available relays and meters used for protection and metering, are designed for low voltage.In addition to the reduction of voltage and current levels, these transformers isolate the measuring or protective circuit from the main circuit which is operating at high power levels. The current transformers reduce the level of current to the instrument or relay operating range, whereas potential transformers transforms the high voltage to a circuit operating low voltage.

Voltactive offer PT’s upto 132KV, 33KV, 11KV class with different ratings.


VOLTACTIVE provides you the complete encapsulation of primary and secondary winding in epoxy resin which prevents penetration of moisture into windings. Contrary to the conventional dry type transformers, the cast coil transformers are better in respect of impulse voltage withstand strength. The cast resin offers very good protection against adverse ambient conditions. These transformers can work without disruption of service at 100% humidity.

These transformers are generally smaller in dimensions and lesser in weights. The construction and installation cost for the sub-station can be reduced by adopting dry type transformers.

Due to encapsulation of coils with cast resin the coils dimensions are stable & no coil tightening is required to maintain the short circuit strength. Also no check of oil level and electrical insulation/oil is required. This leads to saving in cost on account of maintenance.

Voltactive  can manufacture upto 1000KV 11KV/433V with best quality.


Phasellus non lorem quis erat scelerisque efficitur. Nullam mattis odio magna, vel viverra magna viverra nec. Pellentesque habitant morbi tristique senectus et netus et malesuada fames ac turpis egestas. Donec mattis fermentum diam, vitae dictum est convallis et. Aenean mauris lorem, sodales eget condimentum nec, faucibus vitae est. Fusce vulputate odio non mollis commodo. Curabitur efficitur id tellus at imperdiet. Vestibulum commodo dui non eros fringilla, eget sagittis enim placerat. Integer sed nunc leo. Donec interdum felis tortor, finibus fringilla nisi finibus id. Sed placerat, felis ut laoreet semper, nisi ante ullamcorper lacus, at tincidunt elit metus non nibh. Fusce suscipit orci est, tincidunt eleifend odio porttitor et. Aliquam ac velit non orci ullamcorper molestie at ac enim. Curabitur in placerat mi.

Mauris dignissim efficitur magna nec pellentesque. Curabitur vulputate, ligula nec dictum tempus, metus urna aliquet nisl, sed consequat nisi nisl sit amet lectus. Integer ac ornare dui. Mauris est lacus, ullamcorper ac tellus id, ultricies volutpat nisi. Class aptent taciti sociosqu ad litora torquent per conubia nostra, per inceptos himenaeos. Quisque semper quis purus vel aliquam. Donec hendrerit pharetra suscipit. Fusce tristique ipsum elit, id vestibulum nibh feugiat id. Integer volutpat nibh et sem imperdiet, eget dapibus diam laoreet. Praesent feugiat nibh sed magna ullamcorper, nec viverra mi tristique. Fusce rhoncus sapien ultrices, porttitor lectus id, condimentum dui. Etiam at iaculis nisl. Duis vulputate, erat at hendrerit tristique, enim velit luctus dui, in malesuada augue ex quis elit. Maecenas libero dui, venenatis ut lorem quis, hendrerit aliquam odio. Cras sit amet faucibus erat.


Industrial voltage stabilizers are used for supplying continuous output and input voltage in situations of fluctuating power supply. These stabilizers maintain the load conditions and protect the sensitive and expensive electronic items from damage.These can be used in industries, household appliances and lightings,agriculture etc.. for voltage fluctuations.

Voltactive manufactures upto 500V/400V


A lightning arrester is a device used on electrical power systems and telecommunications systems to protect the insulation and conductors of the system from the damaging effects of lightning. The typical lightning arrester has a high-voltage terminal and a ground terminal. When a lightning surge travels along the power line to the arrester, the current from the surge is diverted through the arrestor, in most cases to earth. The lightning arrestor protects the structure from damage by intercepting flashes of lightning and transmitting their current to the ground. Since lightning strikes tends to strike the highest object in the vicinity, the rod is placed at the apex of a tall structure. It is connected to the ground by low-resistance cables. In the case of a building, the soil is used as the ground, and on a ship, water is used. A lightning rod provides a cone of protection, which has a ground radius approximately, equal to its height above the ground.

Voltactive manufacture upto 33kv ,11kv 10ka & 5ka station and line type


A Capacitor Bank is a group of several capacitors of the same rating that are connected in series or parallel with each other to store electrical energy . The resulting bank is then used to counteract or correct a power factor lag or phase shift

We manufacture capacitor banks up to 11kv 1000kva